HomeFong Video Doorbell 1080P for Video Intercom 140° Wide Angle Outdoor Waterproof IR Night Vision RFID IC Card Password Unlock

AHD 1080P Wired Video Doorbell for Video Intercom

Camera sensor 1/3" CMOS , 1080P
Lens Angle: 140 degree (diagonal line )
Night Vision : Infrared night vision
Electronic lock support
Power Consumption 200mA Max.
Material aluminium alloy panel
Waterproof IP65
Operation Temp. -40degc +60degc
Installation Wall mounted

Modify the management password

In standby mode:
enter the management password "123456" +"#" to enter the setting mode,
Press “0”+ “#” to set a new management password,
enter the new 6-digit management password and press “#” to confirm and return to the setting mode.
Note:
If you forget the management password, long press the setting button for 3 seconds, then press the setting button three times in a row, the machine will ring “Bi-Bi-Bi” three times and return to the factory setting state (all data deletion) please be careful Use this feature.

Increase the unlock password

In standby mode:
Enter the management password "123456" +"#" to enter the setting mode Press "1" + "#" to increase the unlock password,
enter the 3- digit serial number "XXX(000-199)" + "#"; "XXXXXX"
(6-bit unlock password) + "#", machine (long ring Bi
One sound, continue to enter the next set of passwords,
then press # key to save, (serial number plus one) Press * to return to the setting mode (or wait 30 seconds to return to standby).
Example:
Set the password for serial number 001 to 223344 (1234
56+#+1+#+001+#+223344+#)

Delete the unlock password

A:In standby mode:
enter the management password "123456"+ "#" to enter the setting mode Press "2" + "#" to delete the unlock password,
enter 3 digits "XX X(000-199)" + unlock password group number + "#",
press # key to delete (long ring Bi), press * key to return to setting mode (or wait 30 seconds to return to standby).
B: In standby mode:
enter the management password
"123456"+ "#" to enter the setting mode Press 2+ “#” to delete the unlock password, and enter “99” + “#” to delete the password.

Add an IC card

A: In standby mode: enter the management password "123456" "#" to enter the setting mode Press 3 "#" to add the IC card, input 3 "XXX (000-199)" unlock card
number group number "#"put the proximity card on the sensing keyboard position, read the card number and successfully sound "B" for a long time, change
The next card continues to be added (group number1)
press the * button to return to the setup mode (or wait 30 seconds to return to standby).
B: Press the setting button in standby mode to enter
the card-increasing state,and the card can be added.
The software will automatically save the card number
from 000-199, and then search for the blank position from low to high,
and then press the setting button to return to the standby state.

Delete card number

A: In standby mode: enter the management password
"123456" + "#" to enter the setting mode Press "4" + "#" to delete the unlock card number, enter 3 digits "XXX (000-199)" unlock card number group number
+ "#" delete (long ring B),
B: in standby mode: enter the management password
“123456”+“#” enters the setting mode, press “4”+“#” to delete the unlocking card number, put the card to be deleted in the sensing area, and the reading is
successful after a long beep.Press the * button to return to the setup mode (or wait 30
seconds to return to standby).
C: In standby mode: enter the management password
"123456"+ "#" to enter the setting mode Press "99" + "#" to delete all passwords.

Keyboard backlight settings

In standby mode: enter the management password "123456" + "#" to enter the keyboard light setting mode
"00" + "#" (off)
“01”+“#” (lights up)
“02”+“#” (off during standby, light when working)