50ml Gap adhesive Screw Glue Quickly Cured Thread Locking Agent Anaerobic Adhesive Corrosion-Resistant Anti-Loosening Glue

1. Name: Thread locking anaerobic adhesive
2. Color: red
3. Shelf life: one year
4. Characteristics: high strength, impact resistance, carry corrosion
5. Storage: 15-28 degrees in a cool place.
6. Packing list: 1pc

Name: Thread Lock Anaerobic Adhesive
Usage Method

Pre-treatment to clean the surface of the assembly to ensure that there is no residual oil, grease, such as motor oil, rust oil, etc., most surfaces do not need to carry out special pre-treatment, for the bonding of the substrate, you need to cooperate with the accelerator pre-treatment.

Gluing:Take appropriate amount of the product and apply it evenly on the threaded surface.

Deglueing:The overflow of glue will not be cured, just wipe it off.

Dismantling Method

1、Disassembly with standard hand tools
2. In rare cases, it is impossible to disassemble the bolt and nut at room temperature due to the long length of the fit.
In rare cases where the length of the fit is so long that it cannot be dismantled at room temperature, the bolt and nut can be locally heated to 250°C and dismantled while still hot.
3. Locally heat the assembly to approx. 250*c and dismantle it while it is still hot. Cleaning method.

Cleaning: For cured glue, soak it in solvent or use a pot brush or other tools for mechanical sanding.

For cured glue, it can be soaked in solvent or mechanically abraded with a pot brush or other tool.

Storage Method
Ideal storage conditions for this product are in a cool, dry place within the temperature range of 8°28°C, in the original packaging, if the product is stored at a temperature of 8~18°C conditions will be more ideal. To avoid contamination of unused adhesive, no adhesive should be poured back into the original packaging.

Model: 243 thread locking adhesive
Specification: 50ml
Special effect: medium strength - thixotropic viscosity
Viscosity: 1300/3000
Curing time: 20 minutes/24 hours
Dismantling torque: 7 (N.m)
Temperature range: -54/150 ℃
Relative density: 1.08
Maximum filling gap: 0.127mm
Description: Fast curing, suitable for inert surfaces, good oil tolerance. Easy to disassemble,
Can be used on work surfaces with slight oil pollution. Used for M20 Locking and sealing of the lower thread.

Model: 242 thread locking adhesive
Specification: 50ml
Special effect: medium strength - thixotropic viscosity
Viscosity: 1200/5000
Curing time: 20 minutes/24 hours
Dismantling torque: 4.9 (N.m)
Temperature range: -54/150 ℃
Relative density: 1
Maximum filling gap: 0.127mm
Description: Universal type, thixotropic viscosity; Used for locking and sealing M6-M20 threads. Can be used for tool disassembly and has a certain degree of lubricity to achieve precise clamping load.

Model: 222 thread locking adhesive
Specification: 50ml
Special effects: low strength, detachable, anti loosening
Viscosity: 1200/1500
Curing time: 20 minutes/24 hours
Dismantling torque: 3.4 (N.m)
Temperature range: -54/150 ℃
Relative density: 1.05
Maximum filling gap: 0.127mm
Description: Used for most metal surfaces and can be disassembled with ordinary tools. Used for locking and sealing M2-M12 threads. The best effect is achieved when applied to fasteners with a diameter of no more than 1/4 #, with a certain degree of lubricity to achieve precise clamping load.

Model: 271 thread locking adhesive
Specification: 50ml
Special effects: high strength, leak proof, anti loosening
Viscosity: 400/600
Curing time: 20 minutes/24 hours
Dismantling torque: 25-40 (N.m)
Temperature range: -54/150 ℃
Relative density: 1.1
Maximum filling gap: 0.127mm
Explanation: Medium viscosity, used for permanent locking and sealing of threads below M36.

Model: 263 thread locking adhesive
Specification: 50ml
Special effects: high strength, leak proof, anti loosening
Viscosity: 400/600
Curing time: 20 minutes/24 hours
Dismantling torque: 32 (N.m)
Temperature range: -54/150 ℃
Relative density: 1.1
Maximum filling gap: 0.127mm
Explanation: Fast curing, can be used on inert surfaces, good oil tolerance. Easily removable, can be used on slightly oil-contaminated work surfaces. For locking and sealing of threads up to M20.

Model: 648 Cylindrical Component Retaining Adhesive
Specification: 50ml
Special effect: High strength, fast curing
Viscosity: 400-600
Curing time: 5 minutes/24 hours
Shear strength: 3625 (psi)
Temperature range: -54/150 ℃
Relative density: 1.13
Maximum filling gap: 0.1524mm
Explanation: Can be used in continuous operating temperatures up to 175 ° C Filling gap of 0.1524mm or less. Initial curing within 5 minutes.

Model: 290 thread locking adhesive
Specification: 50ml
Special effects: Medium strength, penetration grade, detachable
Viscosity: 25-55
Curing time: 20 minutes/24 hours
Dismantling torque: 29 (N.m)
Temperature range: -54/150 ℃
Relative density: 1.12
Maximum filling gap: 0.254mm
Description: Used for locking and sealing of assembled M2-M12 threads. It can also be used for sealing welds, casting sand holes, and other micropores below 0.254mm. To prevent thread rust and corrosion, local heating and tool use are required during disassembly.

Model: 638 Cylindrical Component Retaining Adhesive
Specification: 50ml
Special effect: High strength, fast curing
Viscosity: 2000-3000
Curing time: 5 minutes/24 hours
Shear strength: 3625 (psi)
Temperature range: -54/150 ℃
Relative density: 1.09
Maximum filling gap: 0.381mm
Explanation: The strong retaining adhesive for dynamic or cyclic loading, for holding shaft-hole fits with a clearance of up to 0.381 mm. Initial curing in 5 minutes.